Products \ Equipment - heavy bending machines

It is made of waterproof and durable fabric (tarpaulin). It protects the machine from dust, rain and mud during the transport. The cover is delivered in a bag made of the same fabric. [...]

SPRING LOADED SOLENOIDS, make it easier to bend sheet metal, so time and energy of the worker can be saved.[...]

P-300 Roll Former is a modern tool for profiling and reinforcing flat sheet metal such as wall panels, decorative panels, elevation moulding, facades, lucarnes, verges of gutter flashing and others, according to your imagination. Thanks to our Roll Former you can create your individual style and decorations by making an interesting form in a fast, easy way.  [...]

They allow for regulation of the right angle in relation to knife cutting the sheet metal. The regulation is simplified by an arm close-coupled with two spans which set the side fenders of the sheet metal angle by moving it forward and back.[...]

If the bending machine is not equipped with the back table, back fenders can be bought independently. That lowers the purchasing cost siginifcantly. Back fenders are fast-fixing aluminium span with scale of 1000 mm and movable fenders. ATTENTION! BACK FENDERS WITH MOVABLE BUSH AND SCALE ARE INCLUDED IN BACK TABLE SET. [...]

The machine can be equipped with the device which, with low additional costs, eliminates the costs of buying an expensive segmental bar folder. There are two elements which raises the upper beam to the arbitrary height (but not higher than 90 mm). For example, you have to bend a 500 mm x 500 mm x 50 mm (height) sheet metal from four sides. To do so, you have to raise the holding-down beam to the level of 50 mm (you can use scales) and fix the beam at the proper level.  The sheet metal should be incised at the angles.  Next, you should make or buy a 50 (height) mm x 500 (length) mm profile (instead of metal block you can use a wooden one).  The time for switching is similar to the time which is needed for switching in the segmental bar folder.  You should remember that the pressing force should be balanced and therefore you should put 50mm-high blocks next to the leading columns.  The machine is now prepared to bend a box (baking pan). Maximum dimensions which can be achieved while making a box corresponds to working length of particular bending machine and maximum height of 90 mm.[...]

The lock is put on the main beam column and thus it prevents outside people from using the machine. It is a standard equipment.[...]

Wheels for the heavy manual bending machine (ENCLOSED TO THE MACHINE).[...]

SPRING LOADED SOLENOIDS, make it easier to bend sheet metal, so time and energy of the worker can be saved.[...]

It prevents the roofer from the harmful effects of wet and cold ground. The main function of the platform is the elimination of the movements of the machine. It is worker’s weight that make the machine stand still during the work (especially during the final phase of bending sheet metal). The platform is connected to the machine with the hinges thanks to which the worker can lift the platform during the transport. There is a catch thanks to which the platform does not fall automatically. The permissible load of the platform equals 350 kg. http://www.youtube.com/watch?v=bEXLgk5qdC8[...]

It prevents cut sheet metal strips from falling down on step-on platform and worker’s feet. The clamping bar is located on the front limiters at knee-level.  It is made of wood. There is a possibility to widen the bar when the metal strips are wider.  This device is a very comfortable tool for the worker because there is no need to bend down for the strips.[...]

They are located on the edges of the bending beam. The application of the catches eliminated onerous screwing down and unscrewing. Side handles are used for bending of sheet metal which is so large that there is no access to the horizontal lever of the bending beam.  Another advantage of these devices is the possibility of using them as a help for the person who bends using bending beam.  When the handles are not being used, they should be taken out because they may be dangerous for people who are around the machine during the work.   http://www.youtube.com/watch?v=3IsKZRqjsug[...]

They are used for sheet metal striped cutting. The range of the cutting is between 0 mm and 400 mm. There is a possibility to produce longer limiters upon customer's request.  The limiters are equipped with the wind-up measuring tape which can be easily changed when used up.  In case when the cut sheet metal is narrower than the span of the front limiters, the profile which is equipped with the limiters should be used. The profile should be put on the protruding, pulling out pins. The magnet which are put into limiters should hold the profile still. One can also put pins into the holes of the profile. If the strip of sheet metal is wider than 250 mm, the roofer should support the sheet metal with his hand.  If there is no support the slitter knife will be pushed aside and this may lead to the wrong cutting of the sheet metal.  The construction of the limiters allows for the fast slipping of the limiters under the machine with no need for taking them out.  To block the limiters there is a special handwheel (no need to use spanners).  The limiters scaling should be done individually wi[...]

The technology of setting the limiter is identical as in single position bent plate angle limiter. This device is adapted for setting simultaneously four different angles in the range of 0 to 160 degrees.  The change of the position of the limiters changes when roofer turn the handwheel on which there are numbers from 1 to 4.  The handwheel is located in the middle part of the machine at knee-level.  This limiter can be used for the windowsills production where there are various angles needed.  Thanks to our device, there is no need to change the limiters every time the bending angle changes. It saves time and work. ATTENTION! THE SINGLE POSITION BENT PLATE ANGLE LIMITER AND THE FOUR LIMITERS OF BENT PLATE ARE ASSEMBLED ON THE SAME HANDLES. http://www.youtube.com/watch?v=Ftbo_swHgcI[...]

It enables repetitive bending angle of sheet metal in a lot production. Setting of this device is very simple and fast.  The range of the setting is between 0 and 160 degrees.  The adjustment can be speeded up by looking at the bending angle disc while raising the bending beam.  When the roofer spots the right angle on the disc, he/she should block the limiter.  After the bending, one should check the correctness of the angle on the sheet metal. Adjustments is a consequence of elasticity of the sheet metal.   http://www.youtube.com/watch?v=XCOhTokxxW8[...]

It is made of the steel profiles, fixed to the convenient fasteners. Two profiles are equipped with fenders of a 1000 mm scale. That fenders are used for the repetitive bending or cutting. Additionally, there are wooden elements equipped with fasteners between the profiles. The table is used for comfortable sheet metal cutting and bending. There can be a few sheet metals on the table but if the number of them is high, the support of the table should be used. For transportation the table is packed in a special bag. Attention! Depending on the model of the bending machine, back table consists of various number of elements. http://www.youtube.com/watch?v=dmIcIU-D2xk[...]

It allows cutting sheet metal on the machine. The corpus of the knife is made of steel, covered with dry power lacquer, other elements are covered with zinc. The cutting rollers are made of high-alloy steel which allows for the long-lasting and exact cutting (There is a possibility of multiple sharpening of the cutting rollers). The knife is equipped with the number of possible adjustments which allow for the correction of the trajectory and the position of cutting rollers in relation to the cut sheet metal. During transport the knife is protected by a special bag which is filled with a thick, tough sponge. The hanger is part of the slitter knife. It is a practical, specially shaped tool which perfectly supports the knife when the roofer does not use the knife for a while. The knife is adjusted by the producer of the machine. If any problems occur, please contact us. http://www.youtube.com/watch?v=oo4ishNSXhU[...]

Convenient solution thanks to whichall measuring tools and other useful accessories at in one place. This item is fully rotating.[...]

It enables worker to control visually the angle of sheet metal bending or bending beam.  This device expedites the setting of the single position bent plate angle limiter and the four limiters of bent plate.  To set the correct angle, raise the bending beam to the needed level and counter the limiter of bent plate.  After the bending, one should check the correctness of the angle on the sheet metal. Adjustments is a consequence of elasticity of the sheet metal. [...]

It is used for propping up the back table or the extension of the table to prevent them from excessive load. It is easy to assemble and disassemble. The bag for the table can also be used to transport this device.  The support is equipped with wheels which make them easy to move from one place to another.  The number of supports is dependent on the length of the machine and the cutting or bending technology.[...]

It allows for comfortable moving the sheet metal and its cutting. The convenient fasteners were used in this device. This device is transported in the same bag as the back table. Attention! Depending on the model of the bending machine, the extension of the back table cosists of various number of elements. http://www.youtube.com/watch?v=dmIcIU-D2xk[...]

It is possible to purchase spare cutting rollers in case of damage or sharpening of the rollers.  One set consists of dwo rollers: upper and lower. The discs are placed in bearing which simplifies their exchange. Durability of the discs is very big. If the rollers are used with care, the first exchange of the rollers is to be made after a few years.[...]

The slitter knife bag can be equipped in keys to adjust the machine and first aid kit. [...]